Dresser TD8, TD8C, TD8E Dozer Blade

Dozer blade parts for Dresser TD8 series crawlers, covering cutting edges, pivot pins, bushings, hydraulic angle cylinders, retainer brackets, and blade seal kits across the TD8, TD8C, TD8E, TD8G, and TD8H model range. Both hardware and structural blade components are available to support field repairs and blade rebuilds.

Fits Models At A Glance

• TD8 Series: TD8, TD8C, TD8E, TD8G, TD8H

Key Notes

• Cutting Edges: Center, left-hand, and right-hand cutting edges available for the 90" blade configuration
• Hydraulic Components: Blade angle cylinder and cylinder packing seal kits for TD8C, TD8E, TD8G, and TD8H
• Pivot & Frame Hardware: Includes horizontal main pivot pins, blade frame mounting pins, center mounting pivot pins, and cylinder mounting pins
• Bushings & Retainers: Blade pivot frame bushings, rear mounting bushings, upper and lower blade retainer brackets available
• Cutting Edge Hardware: Bolts and nuts in multiple sizes compatible with Dresser, Case, and CAT applications

Why Choose Broken Tractor

• ✅ Dresser dozer blade parts shipped fast from stock
• ✅ Knowledgeable team covering IH and Dresser crawler lines
• ✅ Two locations serving customers across the US

Frequently Asked Questions

What cutting edges fit a Dresser TD8C, TD8E or TD8G 90 inch blade?

The 90 inch blade on the Dresser TD8C, TD8E and TD8G uses a three-piece cutting edge: center 620690C1, left 620691C1 and right 620692C1. Broken Tractor carries all three, so you can replace a single worn section or the full set. We also carry 3/4 inch cutting edge bolts in 2-1/2 inch (5J4773), 2-3/4 inch (5J4771) and 3 inch (4F0138) lengths, plus the matching 3/4 inch nut (2J3506). Match the bolt length to the bolts you are removing.

Should I replace or reseal the blade angle cylinder on a Dresser TD8?

You can do either, because Broken Tractor offers both a complete hydraulic blade angle cylinder (620630C92) for the TD8C, TD8E and TD8G and a cylinder packing seal kit (626230C6) for the TD8C, TD8E, TD8G and TD8H. The seal kit lets you rebuild your existing cylinder. A complete cylinder replaces the whole unit. We also carry the blade cylinder mounting pin (645351C1) for the TD8C, TD8E and TD8G.

What pivot pins and bushings hold the blade on a Dresser TD8C or TD8E?

The Dresser TD8C and TD8E blade uses the horizontal main blade pivot pin (620693C2), the blade center mounting pivot pin (620664C1) and the blade frame mounting pin (620873C2). The matching bushings include the blade pivot frame bushing (618962C1), the rear mounting blade frame bushing (620665C1) and the blade bushing (705734C1). Broken Tractor also carries the upper blade retainer (705760C1) and lower blade retainer bracket (646670C1) to finish a blade pivot rebuild.

Do Dresser TD8 blade parts fit the original TD8 and the TD8H?

Some do, but most parts are listed for the TD8C, TD8E and TD8G. For the original TD8, we carry the blade pivot frame bushing (618962C1) and the 90 inch wide blade face (PV512). For the TD8H, we carry the horizontal main pivot pin (620693C2), the rear mounting blade frame bushing (620665C1) and the cylinder packing seal kit (626230C6). Fitment can vary by model and serial number, so match the part number from your old part or call (800) 909-7060 to confirm before ordering.

Can I replace the blade face on a Dresser TD8 dozer?

Yes, Broken Tractor offers a 90 inch wide dozer blade face (PV512) that fits the Dresser TD8, TD8C and TD8E. It is a structural replacement for a worn or damaged blade face. You can pair it with new center, left and right cutting edges and cutting edge bolts to complete a blade rebuild.